Chain Link Fence costs $11.95 to $29.87 per linear ft in Grand Forks in 2026. For a 150-foot run, expect $1,793 – $4,481 installed, typically near $3,137. That is essentially in line with the North Dakota state average.
Grand Forks chain link fence calculator
Planning estimate only. State pricing applies a construction wage index to the labor share; materials are held at national prices. Get three written quotes before committing.
Why Grand Forks costs more than the rest of North Dakota
Grand Forks carries essentially the same rate as the North Dakota statewide figure. Wages, permitting, and site access here track close to the statewide norm, so the premium metro buyers often pay elsewhere is much smaller in Grand Forks.
Statewide, North Dakota averages $11.95 to $29.87 per linear ft, against $11.95 to $29.87 inside Grand Forks. Suburbs on the metro fringe usually fall between the two.
Chain Link Fence cost by project size in Grand Forks
| Project size | Grand Forks range | Typical |
|---|---|---|
| 50 ft | $597 – $1,493 | $1,045 |
| 100 ft | $1,195 – $2,987 | $2,091 |
| 150 ft | $1,792 – $4,480 | $3,136 |
| 200 ft | $2,389 – $5,973 | $4,181 |
| 250 ft | $2,987 – $7,466 | $5,226 |
| 300 ft | $3,584 – $8,960 | $6,272 |
| 400 ft | $4,778 – $11,946 | $8,362 |
| 500 ft | $5,973 – $14,933 | $10,453 |
Where the money actually goes
For a 150-foot run in Grand Forks at roughly $3,137, a typical bill splits like this:
| Line item | Share | Cost |
|---|---|---|
| Labor | 45% | $1,411 |
| Materials | 41% | $1,294 |
| Site prep & equipment | 8% | $259 |
| Overhead, disposal & finishing | 6% | $172 |
The labor share is why identical projects diverge so sharply between states. It is also why a bid that comes in far below these numbers usually means a thinner specification or a crew cutting preparation, not a genuine bargain.
Grand Forks compared with other North Dakota markets
| Area | Cost per linear ft | vs Grand Forks |
|---|---|---|
| Fargo | $12.54 – $31.36 | +5% |
| Bismarck | $12.18 – $30.46 | +2% |
| North Dakota average | $11.95 – $29.87 | 0% |
Frost depth and code requirements in Grand Forks
Permits in Grand Forks
A residential permit for this work typically runs around $300 in North Dakota, and metro jurisdictions like Grand Forks usually sit at the upper end of that range with longer review times. Permit cost is rarely included in a contractor quote, so add it separately. Confirm scope with the Grand Forks building department before work begins.
Hiring in Grand Forks
Get three written, itemised quotes from licensed and insured contractors, and make sure each specifies the same scope and the same grade of material. In a metro market, the cheapest bid often reflects a thinner specification or a crew travelling in from outside the area rather than a genuine saving. Ask for local references and check that the licence is current in North Dakota.
Frequently asked questions
How much does chain link fence cost in Grand Forks?
In 2026, chain link fence costs $11.95 to $29.87 per linear ft in Grand Forks. For a 150-foot run, the installed total typically lands between $1,793 and $4,481.
Is Grand Forks more expensive than the rest of North Dakota?
Not meaningfully. Grand Forks prices essentially in line with the North Dakota statewide average.
Do I need a permit in Grand Forks?
Most work of this type and value requires a permit. Budget around $300 and allow extra time for review, since metro jurisdictions are typically slower than rural ones.
How do I compare quotes in Grand Forks?
Insist on three written, itemised quotes covering identical scope, materials, and preparation. A bid far below the others usually signals a reduced specification rather than better value.
Nearby markets
Open the full chain link fence calculator →