Stamped Concrete costs $12.85 to $27.68 per sq ft in Utah in 2026. For a 400 sq ft project, that puts the installed total at $5,140 – $11,070, with most projects landing near $8,105. Utah is essentially in line with the national average.
Why Utah prices differ from the national average
Roughly 58% of the installed cost of stamped concrete is labor, and labor is the part of the bill that actually moves between states. Utah construction wages average $36.23 per hour against a national figure near $36.97 — a wage index of 0.98×.
Materials behave differently. Ready-mix concrete, rebar, mesh, and forming lumber are priced on national and regional commodity markets, so they barely move from one state to the next. That is why we apply the wage index only to the labor share and hold materials at national prices. Doing that puts Utah at $12.85 to $27.68 per sq ft, against a national baseline of $13.00 to $28.00.
Two other forces sit on top of that. Metro areas inside Utah price above the statewide figure because of wages, permitting, and site access. And the state’s deep frost line adds excavation and below-grade volume that southern states never pay for.
Stamped Concrete cost by project size in Utah
These figures apply the Utah rate to common project sizes. They cover a standard specification with normal site access.
| Project size | Utah cost range | Typical |
|---|---|---|
| 10×10 (100 sq ft) | $1,285 – $2,768 | $2,026 |
| 12×12 (144 sq ft) | $1,850 – $3,985 | $2,918 |
| 12×16 (192 sq ft) | $2,467 – $5,314 | $3,890 |
| 16×20 (320 sq ft) | $4,112 – $8,856 | $6,484 |
| 20×20 (400 sq ft) | $5,140 – $11,070 | $8,105 |
| 24×24 (576 sq ft) | $7,401 – $15,941 | $11,671 |
| 30×40 (1,200 sq ft) | $15,419 – $33,210 | $24,315 |
Where the money actually goes
For a 400 sq ft project in Utah at roughly $8,105, a typical bill splits like this:
| Line item | Share | Cost |
|---|---|---|
| Labor | 58% | $4,701 |
| Materials | 32% | $2,553 |
| Site prep & equipment | 6% | $511 |
| Overhead, disposal & finishing | 4% | $340 |
The labor share is why identical projects diverge so sharply between states. It is also why a bid that comes in far below these numbers usually means a thinner specification or a crew cutting site prep, not a genuine bargain.
Stamped Concrete cost by city in Utah
Statewide averages hide a lot. Salt Lake City, Provo, St. George all price above the Utah average, while rural counties run below it:
| Area | Cost per sq ft | A 400 sq ft project | vs state |
|---|---|---|---|
| Salt Lake City | $14.13 – $30.44 | $8,915 | +10% |
| Provo | $13.49 – $29.06 | $8,510 | +5% |
| St. George | $13.36 – $28.78 | $8,429 | +4% |
| Rural Utah | $11.95 – $25.74 | $7,538 | −7% |
What is included in a Utah quote — and what is not
A complete quote for this work should list dimensions, specification and grade, site preparation, materials, labor, cleanup, and disposal. Those are the items already reflected in the ranges above.
Costs that usually sit outside the headline number: permits (around $450 in Utah), demolition or removal of existing work, unusual site access, drainage or grading corrections, and any upgrade to the standard specification. When two bids differ by thousands, the gap is nearly always one of these, not the labor rate.
Frost depth and code requirements in Utah
Permits in Utah
A residential permit for work of this type and value in Utah typically runs around $450, though the figure varies by municipality and often scales with declared project value. Permit cost is rarely folded into a contractor’s per-sq ft quote, so add it separately when comparing bids. Confirm requirements with your local building department before work begins — unpermitted work can surface later during a sale or insurance claim.
Best time of year to schedule in Utah
Utah has a solid working season from spring through late autumn, with a genuine winter slowdown. Demand peaks in late spring and early summer, which is also when quotes are highest. Scheduling in early spring or after the autumn rush often saves money.
DIY versus hiring a contractor in Utah
Materials account for roughly 42% of the installed price, so a 400 sq ft project carries about $3,404 in materials against an installed cost near $8,105. The gap is labor, equipment, and the risk of getting it wrong.
Because Utah labor runs at 0.98× the national rate, the DIY saving here is closer to the national norm. Weigh it against tool rental, waste disposal, permit responsibility, and the fact that remedial work almost always costs more than doing it right the first time.
How Utah compares with nearby states
Utah sits in the West region. Here is how neighbouring states price the same specification:
| State | Cost per sq ft | vs Utah |
|---|---|---|
| Idaho | $12.25 – $26.38 | Lower than Utah |
| New Mexico | $12.25 – $26.38 | Lower than Utah |
| Montana | $12.32 – $26.54 | Lower than Utah |
| Wyoming | $12.77 – $27.51 | Lower than Utah |
| Arizona | $12.92 – $27.84 | Higher than Utah |
| Nevada | $13.38 – $28.81 | Higher than Utah |
Getting an accurate number for your project
Everything above is a planning range. Enter your real dimensions and specification to get a figure with Utah rates already applied:
Open the stamped concrete calculator →Then get three written, itemised quotes. Make sure each one specifies the same dimensions and the same grade of material — that is the only way a comparison means anything.
Frequently asked questions
How much does stamped concrete cost in Utah?
In 2026, stamped concrete costs $12.85 to $27.68 per sq ft in Utah. For a 400 sq ft project, the installed total typically lands between $5,140 and $11,070, with most projects near $8,105.
Is stamped concrete more expensive in Utah than the national average?
Utah is essentially in line with the national average. The driver is a construction wage index of 0.98 times the national figure, applied to the roughly 58% of the project cost that is labor.
Which parts of Utah are most expensive?
Salt Lake City, Provo, and St. George price above the statewide average because of higher wages, stricter permitting, and tighter site access. Rural counties typically run around 7% below the state figure.
Do I need a permit in Utah?
Most municipalities in Utah require a permit for work of this type and value. Budget around $450 and confirm with your local building department before work starts, since requirements vary between cities and counties.
How deep is the frost line in Utah?
The frost line in Utah is roughly 30 inches. Footings and posts must extend below that depth to avoid frost heave, which adds excavation and material to the job.
When is the cheapest time to book this work in Utah?
Utah has a solid working season from spring through late autumn, with a genuine winter slowdown. Demand peaks in late spring and early summer, which is also when quotes are highest. Scheduling in early spring or after the autumn rush often saves money.
How much of the cost is labor versus materials?
Labor is about 58% of the installed price and materials about 42%. That split is why state wage differences move the total so much, and why material price swings move it less than people expect.
Why do contractor quotes in Utah vary so much?
Three things move a quote most: metro versus rural location, site access and preparation, and the specification itself. Two bids are only comparable when both list the same dimensions, the same grade of material, and the same scope of prep work.