Metal Roof costs $9.09 to $22.22 per sq ft in Texas in 2026. For a 400 sq ft project, that puts the installed total at $3,636 – $8,888, with most projects landing near $6,262. Texas is essentially in line with the national average.
Why Texas prices differ from the national average
Roughly 50% of the installed cost of metal roof is labor, and labor is the part of the bill that actually moves between states. Texas construction wages average $37.71 per hour against a national figure near $36.97 — a wage index of 1.02×.
Materials behave differently. Shingles, panels, underlayment, and flashing are priced by national manufacturers, so material costs barely move from one state to the next. That is why we apply the wage index only to the labor share and hold materials at national prices. Doing that puts Texas at $9.09 to $22.22 per sq ft, against a national baseline of $9.00 to $22.00.
Two other forces sit on top of that. Metro areas inside Texas price above the statewide figure because of wages, permitting, and site access. And local weather exposure drives the specification, and stricter wind or snow requirements raise both material and labor cost.
Metal Roof cost by project size in Texas
These figures apply the Texas rate to common project sizes. They cover a standard specification with normal site access.
| Project size | Texas cost range | Typical |
|---|---|---|
| 1,000 sq ft roof | $9,090 – $22,220 | $15,655 |
| 1,500 sq ft roof | $13,635 – $33,330 | $23,483 |
| 2,000 sq ft roof | $18,180 – $44,440 | $31,310 |
| 2,500 sq ft roof | $22,725 – $55,550 | $39,138 |
| 3,000 sq ft roof | $27,270 – $66,660 | $46,965 |
| 3,500 sq ft roof | $31,815 – $77,770 | $54,793 |
Where the money actually goes
For a 400 sq ft project in Texas at roughly $6,262, a typical bill splits like this:
| Line item | Share | Cost |
|---|---|---|
| Labor | 50% | $3,131 |
| Materials | 38% | $2,348 |
| Site prep & equipment | 8% | $470 |
| Overhead, disposal & finishing | 5% | $313 |
The labor share is why identical projects diverge so sharply between states. It is also why a bid that comes in far below these numbers usually means a thinner specification or a crew cutting site prep, not a genuine bargain.
Metal Roof cost by city in Texas
Statewide averages hide a lot. Houston, Dallas, Austin all price above the Texas average, while rural counties run below it:
| Area | Cost per sq ft | A 400 sq ft project | vs state |
|---|---|---|---|
| Houston | $9.82 – $24.00 | $6,763 | +8% |
| Dallas | $10.00 – $24.44 | $6,888 | +10% |
| Austin | $10.36 – $25.33 | $7,139 | +14% |
| Rural Texas | $8.45 – $20.66 | $5,824 | −7% |
What is included in a Texas quote — and what is not
A complete quote for this work should list dimensions, specification and grade, site preparation, materials, labor, cleanup, and disposal. Those are the items already reflected in the ranges above.
Costs that usually sit outside the headline number: permits (around $450 in Texas), demolition or removal of existing work, unusual site access, drainage or grading corrections, and any upgrade to the standard specification. When two bids differ by thousands, the gap is nearly always one of these, not the labor rate.
Weather exposure and code in Texas
Permits in Texas
A residential permit for work of this type and value in Texas typically runs around $450, though the figure varies by municipality and often scales with declared project value. Permit cost is rarely folded into a contractor’s per-sq ft quote, so add it separately when comparing bids. Confirm requirements with your local building department before work begins — unpermitted work can surface later during a sale or insurance claim.
Best time of year to schedule in Texas
Texas allows year-round work, so there is no hard seasonal shutdown. The practical constraints are summer heat, which can force early-morning pours and rain delays in the wet season. Late autumn and winter are often the quietest and cheapest times to book a crew.
DIY versus hiring a contractor in Texas
Materials account for roughly 50% of the installed price, so a 400 sq ft project carries about $3,131 in materials against an installed cost near $6,262. The gap is labor, equipment, and the risk of getting it wrong.
Because Texas labor runs at 1.02× the national rate, the DIY saving here is closer to the national norm. Weigh it against tool rental, waste disposal, permit responsibility, and the fact that remedial work almost always costs more than doing it right the first time.
How Texas compares with nearby states
Texas sits in the South region. Here is how neighbouring states price the same specification:
| State | Cost per sq ft | vs Texas |
|---|---|---|
| Mississippi | $8.19 – $20.02 | Lower than Texas |
| Arkansas | $8.24 – $20.13 | Lower than Texas |
| Alabama | $8.28 – $20.24 | Lower than Texas |
| West Virginia | $8.37 – $20.46 | Lower than Texas |
| Oklahoma | $8.42 – $20.57 | Lower than Texas |
| Kentucky | $8.46 – $20.68 | Lower than Texas |
Getting an accurate number for your project
Everything above is a planning range. Enter your real dimensions and specification to get a figure with Texas rates already applied:
Open the metal roof calculator →Then get three written, itemised quotes. Make sure each one specifies the same dimensions and the same grade of material — that is the only way a comparison means anything.
Frequently asked questions
How much does metal roof cost in Texas?
In 2026, metal roof costs $9.09 to $22.22 per sq ft in Texas. For a 400 sq ft project, the installed total typically lands between $3,636 and $8,888, with most projects near $6,262.
Is metal roof more expensive in Texas than the national average?
Texas is essentially in line with the national average. The driver is a construction wage index of 1.02 times the national figure, applied to the roughly 50% of the project cost that is labor.
Which parts of Texas are most expensive?
Houston, Dallas, and Austin price above the statewide average because of higher wages, stricter permitting, and tighter site access. Rural counties typically run around 7% below the state figure.
Do I need a permit in Texas?
Most municipalities in Texas require a permit for work of this type and value. Budget around $450 and confirm with your local building department before work starts, since requirements vary between cities and counties.
What weather requirements affect roofs in Texas?
Texas roofs face heat, UV exposure, and storm risk rather than snow. In coastal and hurricane-exposed counties, wind-rating and fastening requirements are stricter, which raises both material and labor cost against inland areas.
When is the cheapest time to book this work in Texas?
Texas allows year-round work, so there is no hard seasonal shutdown. The practical constraints are summer heat, which can force early-morning pours and rain delays in the wet season. Late autumn and winter are often the quietest and cheapest times to book a crew.
How much of the cost is labor versus materials?
Labor is about 50% of the installed price and materials about 50%. That split is why state wage differences move the total so much, and why material price swings move it less than people expect.
Why do contractor quotes in Texas vary so much?
Three things move a quote most: metro versus rural location, site access and preparation, and the specification itself. Two bids are only comparable when both list the same dimensions, the same grade of material, and the same scope of prep work.