Concrete Driveway costs $9.42 to $21.19 per sq ft in Tacoma in 2026. For a 400 sq ft project, expect $3,767 – $8,476 installed, typically near $6,121. That is about 9% above the Washington state average.
Tacoma concrete driveway cost calculator
Planning estimate only. State pricing applies a construction wage index to the labor share; materials are held at national prices. Get three written quotes before committing.
Why Tacoma costs more than the rest of Washington
Tacoma carries roughly a 9% premium over the Washington statewide figure. Three things drive that gap. Metro wages run above the state average, and labor is about 50% of this bill. Permitting and inspection are slower and more expensive inside city limits. And site access is tighter, which means smaller equipment, more hand work, and sometimes street permits for deliveries.
Statewide, Washington averages $8.64 to $19.44 per sq ft, against $9.42 to $21.19 inside Tacoma. Suburbs on the metro fringe usually fall between the two.
Concrete Driveway cost by project size in Tacoma
| Project size | Tacoma range | Typical |
|---|---|---|
| 10×10 (100 sq ft) | $942 – $2,119 | $1,530 |
| 12×12 (144 sq ft) | $1,356 – $3,051 | $2,204 |
| 12×16 (192 sq ft) | $1,808 – $4,068 | $2,938 |
| 16×20 (320 sq ft) | $3,014 – $6,781 | $4,897 |
| 20×20 (400 sq ft) | $3,767 – $8,476 | $6,121 |
| 24×24 (576 sq ft) | $5,425 – $12,205 | $8,815 |
| 30×40 (1,200 sq ft) | $11,301 – $25,428 | $18,364 |
Tacoma compared with other Washington markets
| Area | Cost per sq ft | vs Tacoma |
|---|---|---|
| Seattle | $10.20 – $22.94 | +8% |
| Spokane | $8.90 – $20.02 | -6% |
| Washington average | $8.64 – $19.44 | −9% |
Ground conditions and code in Tacoma
Permits in Tacoma
A residential permit for this work typically runs around $700 in Washington, and metro jurisdictions like Tacoma usually sit at the upper end of that range with longer review times. Permit cost is rarely included in a contractor quote, so add it separately. Confirm scope with the Tacoma building department before work begins.
Hiring in Tacoma
Get three written, itemised quotes from licensed and insured contractors, and make sure each specifies the same dimensions and the same grade of material. In a metro market, the cheapest bid often reflects a thinner specification or a crew travelling in from outside the area rather than a genuine saving. Ask for local references and check that the licence is current in Washington.
Frequently asked questions
How much does concrete driveway cost in Tacoma?
In 2026, concrete driveway costs $9.42 to $21.19 per sq ft in Tacoma. For a 400 sq ft project, the installed total typically lands between $3,767 and $8,476.
Is Tacoma more expensive than the rest of Washington?
Yes. Tacoma runs about 9% above the Washington statewide average, driven by metro wage levels, permitting, and tighter site access.
Do I need a permit in Tacoma?
Most work of this type and value requires a permit. Budget around $700 and allow extra time for review, since metro jurisdictions are typically slower than rural ones.
How do I compare quotes in Tacoma?
Insist on three written, itemised quotes covering identical dimensions, materials, and scope of preparation. A bid far below the others usually signals a reduced specification rather than better value.
Nearby markets
Open the full concrete driveway calculator →