Concrete Driveway costs $8.64 to $19.44 per sq ft in Washington in 2026. For a 400 sq ft project, that puts the installed total at $3,456 – $7,776, with most projects landing near $5,616. Washington is about 8% above the national average.
Washington concrete driveway cost calculator
Planning estimate only. State pricing applies a construction wage index to the labor share; materials are held at national prices. Get three written quotes before committing.
Why Washington prices differ from the national average
Roughly 50% of the installed cost of concrete driveway is labor, and labor is the part of the bill that actually moves between states. Washington construction wages average $42.89 per hour against a national figure near $36.97 — a wage index of 1.16×.
Materials behave differently. Ready-mix concrete, rebar, mesh, and forming lumber are priced on national and regional commodity markets, so they barely move from one state to the next. That is why we apply the wage index only to the labor share and hold materials at national prices. Doing that puts Washington at $8.64 to $19.44 per sq ft, against a national baseline of $8.00 to $18.00.
Two other forces sit on top of that. Metro areas inside Washington price above the statewide figure because of wages, permitting, and site access. And a moderate frost line adds some excavation depth to footings and posts.
Concrete Driveway cost by project size in Washington
These figures apply the Washington rate to common project sizes. They cover a standard specification with normal site access.
| Project size | Washington cost range | Typical |
|---|---|---|
| 10×10 (100 sq ft) | $864 – $1,944 | $1,404 |
| 12×12 (144 sq ft) | $1,244 – $2,799 | $2,022 |
| 12×16 (192 sq ft) | $1,659 – $3,732 | $2,696 |
| 16×20 (320 sq ft) | $2,765 – $6,221 | $4,493 |
| 20×20 (400 sq ft) | $3,456 – $7,776 | $5,616 |
| 24×24 (576 sq ft) | $4,977 – $11,197 | $8,087 |
| 30×40 (1,200 sq ft) | $10,368 – $23,328 | $16,848 |
Where the money actually goes
For a 400 sq ft project in Washington at roughly $5,616, a typical bill splits like this:
| Line item | Share | Cost |
|---|---|---|
| Labor | 50% | $2,808 |
| Materials | 38% | $2,106 |
| Site prep & equipment | 8% | $421 |
| Overhead, disposal & finishing | 5% | $281 |
The labor share is why identical projects diverge so sharply between states. It is also why a bid that comes in far below these numbers usually means a thinner specification or a crew cutting site prep, not a genuine bargain.
Concrete Driveway cost by city in Washington
Statewide averages hide a lot. Seattle, Spokane, Tacoma all price above the Washington average, while rural counties run below it:
| Area | Cost per sq ft | A 400 sq ft project | vs state |
|---|---|---|---|
| Seattle | $10.20 – $22.94 | $6,627 | +18% |
| Spokane | $8.90 – $20.02 | $5,784 | +3% |
| Tacoma | $9.42 – $21.19 | $6,121 | +9% |
| Rural Washington | $8.04 – $18.08 | $5,223 | −7% |
What is included in a Washington quote — and what is not
A complete quote for this work should list dimensions, specification and grade, site preparation, materials, labor, cleanup, and disposal. Those are the items already reflected in the ranges above.
Costs that usually sit outside the headline number: permits (around $700 in Washington), demolition or removal of existing work, unusual site access, drainage or grading corrections, and any upgrade to the standard specification. When two bids differ by thousands, the gap is nearly always one of these, not the labor rate.
Frost depth and code requirements in Washington
Permits in Washington
A residential permit for work of this type and value in Washington typically runs around $700, though the figure varies by municipality and often scales with declared project value. Permit cost is rarely folded into a contractor’s per-sq ft quote, so add it separately when comparing bids. Confirm requirements with your local building department before work begins — unpermitted work can surface later during a sale or insurance claim.
Best time of year to schedule in Washington
Washington has a solid working season from spring through late autumn, with a genuine winter slowdown. Demand peaks in late spring and early summer, which is also when quotes are highest. Scheduling in early spring or after the autumn rush often saves money.
DIY versus hiring a contractor in Washington
Materials account for roughly 50% of the installed price, so a 400 sq ft project carries about $2,808 in materials against an installed cost near $5,616. The gap is labor, equipment, and the risk of getting it wrong.
Because Washington labor runs at 1.16× the national rate, the DIY saving here is larger than in most states, which makes self-performing more tempting. Weigh it against tool rental, waste disposal, permit responsibility, and the fact that remedial work almost always costs more than doing it right the first time.
How Washington compares with nearby states
Washington sits in the West region. Here is how neighbouring states price the same specification:
| State | Cost per sq ft | vs Washington |
|---|---|---|
| Idaho | $7.60 – $17.10 | Lower than Washington |
| New Mexico | $7.60 – $17.10 | Lower than Washington |
| Montana | $7.64 – $17.19 | Lower than Washington |
| Wyoming | $7.88 – $17.73 | Lower than Washington |
| Utah | $7.92 – $17.82 | Lower than Washington |
| Arizona | $7.96 – $17.91 | Lower than Washington |
Getting an accurate number for your project
Everything above is a planning range. Enter your real dimensions and specification to get a figure with Washington rates already applied:
Open the concrete driveway calculator →Then get three written, itemised quotes. Make sure each one specifies the same dimensions and the same grade of material — that is the only way a comparison means anything.
Frequently asked questions
How much does concrete driveway cost in Washington?
In 2026, concrete driveway costs $8.64 to $19.44 per sq ft in Washington. For a 400 sq ft project, the installed total typically lands between $3,456 and $7,776, with most projects near $5,616.
Is concrete driveway more expensive in Washington than the national average?
Washington is about 8% above the national average. The driver is a construction wage index of 1.16 times the national figure, applied to the roughly 50% of the project cost that is labor.
Which parts of Washington are most expensive?
Seattle, Spokane, and Tacoma price above the statewide average because of higher wages, stricter permitting, and tighter site access. Rural counties typically run around 7% below the state figure.
Do I need a permit in Washington?
Most municipalities in Washington require a permit for work of this type and value. Budget around $700 and confirm with your local building department before work starts, since requirements vary between cities and counties.
How deep is the frost line in Washington?
The frost line in Washington is roughly 18 inches. Footings and posts must extend below that depth to avoid frost heave, which adds excavation and material to the job.
When is the cheapest time to book this work in Washington?
Washington has a solid working season from spring through late autumn, with a genuine winter slowdown. Demand peaks in late spring and early summer, which is also when quotes are highest. Scheduling in early spring or after the autumn rush often saves money.
How much of the cost is labor versus materials?
Labor is about 50% of the installed price and materials about 50%. That split is why state wage differences move the total so much, and why material price swings move it less than people expect.
Why do contractor quotes in Washington vary so much?
Three things move a quote most: metro versus rural location, site access and preparation, and the specification itself. Two bids are only comparable when both list the same dimensions, the same grade of material, and the same scope of prep work.