A 100 ft vinyl fence costs $2,800 to $6,000 installed in 2026, with most projects landing near $4,400. That works out to $28.00 – $60.00 per linear ft. Your state changes the number — use the calculator below.
100 ft Vinyl Fence cost calculator
Planning estimate only. State pricing applies a construction wage index to the labor share; materials are held at national prices. Get three written quotes before committing.
100 ft Vinyl Fence cost by state
Labor is about 42% of the bill, so the same 100 ft project swings widely between states:
| Cheapest states | Cost | Priciest states | Cost |
|---|---|---|---|
| Mississippi | $4,067 | Hawaii | $4,917 |
| Arkansas | $4,086 | California | $4,807 |
| Alabama | $4,104 | New York | $4,770 |
| South Dakota | $4,123 | Massachusetts | $4,733 |
| West Virginia | $4,141 | Washington | $4,696 |
What fits on a 100 ft vinyl fence?
A 100 ft run is the typical back-yard job: enough to enclose the rear boundary of a standard suburban lot, or two sides of a smaller one.
Cost by grade and finish
Specification moves the price as much as size does. For a 100 ft project:
| Option | Typical cost | vs standard |
|---|---|---|
| Standard grade | $4,400 | baseline |
| Mid grade | $5,368 | +22% |
| Premium grade | $6,512 | +48% |
How 100 ft compares with nearby sizes
| Size | Installed cost | vs 100 ft |
|---|---|---|
| 50 ft | $2,200 | -50% |
| 75 ft | $3,300 | -25% |
| 100 ft (this page) | $4,400 | — |
| 120 ft | $5,280 | +20% |
| 150 ft | $6,600 | +50% |
What the price includes
The range above covers materials, labor, standard site preparation, and cleanup for a 100 ft project with normal access. It excludes permits, demolition or removal of existing work, drainage corrections, and upgrades beyond a standard specification.
Materials alone run roughly $2,552 for this size, which is the figure to start from if you are weighing doing it yourself.
What changes the price of a 100 ft vinyl fence
Terrain and slope
Sloped or rocky ground means stepped panels and harder post holes. Both add labor hours that flat-yard estimates do not include.
Gates
Each gate costs far more per foot than plain fence. A single walk gate adds a few hundred dollars; a double drive gate adds substantially more.
Post setting
Concrete-set posts cost more upfront than driven or gravel-set posts but last markedly longer, especially in frost-prone ground.
Material grade
Within any fence type, board thickness, post gauge, and hardware quality create a wide price band for what looks like the same fence.
Removal of old fence
Tear-out and disposal of an existing fence is usually quoted separately, commonly $3 to $8 per linear foot.
How long does a 100 ft vinyl fence take?
A 100 ft fence is usually a one to two day installation. If posts are set in concrete, most installers let them cure overnight before hanging panels, which is why even short runs often span two visits.
Frequently asked questions
How much does a 100 ft vinyl fence cost?
A 100 ft vinyl fence costs $2,800 to $6,000 installed in 2026, averaging about $4,400. State labor rates move that figure by 20% or more in either direction.
How much is that per linear ft?
It works out to $28.00 to $60.00 per linear ft. Larger projects usually land slightly lower per linear ft because setup and mobilisation costs spread across more area.
What would it cost to do it myself?
Materials for a 100 ft project run roughly $2,552. The rest is labor, equipment, and disposal. Factor in tool rental and the cost of correcting mistakes before deciding.
Which states are cheapest for this project?
Mississippi and Arkansas are among the lowest at around $4,067, while Hawaii runs closer to $4,917 for the same specification.
How long does a 100 ft vinyl fence take to complete?
A 100 ft fence is usually a one to two day installation. If posts are set in concrete, most installers let them cure overnight before hanging panels, which is why even short runs often span two visits.
What most often pushes a 100 ft project over budget?
Terrain and slope and gates are the two most common. Sloped or rocky ground means stepped panels and harder post holes. Both add labor hours that flat-yard estimates do not include.
Do I need a permit for a 100 ft vinyl fence?
Most jurisdictions require a permit for work of this type and value, and the fee commonly scales with declared project value. Budget a few hundred dollars and confirm with your local building department before work starts, since unpermitted work can surface during a sale or an insurance claim.
Other vinyl fence sizes
Open the full vinyl fence calculator →