Wood Fence costs $17.28 to $43.20 per linear ft in North Carolina in 2026. For a 150-foot run, that puts the installed total at $2,592 – $6,480, with most projects landing near $4,536. North Carolina is about 4% below the national average.
Why North Carolina prices differ from the national average
Roughly 50% of the installed cost of wood fence is labor, and labor is the part of the bill that actually moves between states. North Carolina construction wages average $34.01 per hour against a national figure near $36.97 — a wage index of 0.92×.
Materials behave differently. Fence panels, posts, rails, and hardware are priced by national manufacturers and distributors, so material costs barely move from one state to the next. That is why we apply the wage index only to the labor share and hold materials at national prices. Doing that puts North Carolina at $17.28 to $43.20 per linear ft, against a national baseline of $18.00 to $45.00.
Two other forces sit on top of that. Metro areas inside North Carolina price above the statewide figure because of wages, permitting, and site access. And a moderate frost line adds some excavation depth to footings and posts.
Wood Fence cost by project size in North Carolina
These figures apply the North Carolina rate to common project sizes. They cover a standard specification with normal site access.
| Project size | North Carolina cost range | Typical |
|---|---|---|
| 50 ft | $864 – $2,160 | $1,512 |
| 100 ft | $1,728 – $4,320 | $3,024 |
| 150 ft | $2,592 – $6,480 | $4,536 |
| 200 ft | $3,456 – $8,640 | $6,048 |
| 250 ft | $4,320 – $10,800 | $7,560 |
| 300 ft | $5,184 – $12,960 | $9,072 |
| 400 ft | $6,912 – $17,280 | $12,096 |
| 500 ft | $8,640 – $21,600 | $15,120 |
Where the money actually goes
For a 150-foot run in North Carolina at roughly $4,536, a typical bill splits like this:
| Line item | Share | Cost |
|---|---|---|
| Labor | 50% | $2,268 |
| Materials | 38% | $1,701 |
| Site prep & equipment | 8% | $340 |
| Overhead, disposal & finishing | 5% | $227 |
The labor share is why identical projects diverge so sharply between states. It is also why a bid that comes in far below these numbers usually means a thinner specification or a crew cutting site prep, not a genuine bargain.
Wood Fence cost by city in North Carolina
Statewide averages hide a lot. Charlotte, Raleigh, Greensboro all price above the North Carolina average, while rural counties run below it:
| Area | Cost per linear ft | A 150-foot run | vs state |
|---|---|---|---|
| Charlotte | $19.18 – $47.95 | $5,035 | +11% |
| Raleigh | $19.01 – $47.52 | $4,990 | +10% |
| Greensboro | $17.63 – $44.06 | $4,627 | +2% |
| Rural North Carolina | $16.07 – $40.18 | $4,218 | −7% |
What is included in a North Carolina quote — and what is not
A complete quote for this work should list dimensions, specification and grade, site preparation, materials, labor, cleanup, and disposal. Those are the items already reflected in the ranges above.
Costs that usually sit outside the headline number: permits (around $400 in North Carolina), demolition or removal of existing work, unusual site access, drainage or grading corrections, and any upgrade to the standard specification. When two bids differ by thousands, the gap is nearly always one of these, not the labor rate.
Frost depth and code requirements in North Carolina
Permits in North Carolina
A residential permit for work of this type and value in North Carolina typically runs around $400, though the figure varies by municipality and often scales with declared project value. Permit cost is rarely folded into a contractor’s per-linear ft quote, so add it separately when comparing bids. Confirm requirements with your local building department before work begins — unpermitted work can surface later during a sale or insurance claim.
Best time of year to schedule in North Carolina
North Carolina allows year-round work, so there is no hard seasonal shutdown. The practical constraints are summer heat, which can force early-morning pours and rain delays in the wet season. Late autumn and winter are often the quietest and cheapest times to book a crew.
DIY versus hiring a contractor in North Carolina
Materials account for roughly 50% of the installed price, so a 150-foot run carries about $2,268 in materials against an installed cost near $4,536. The gap is labor, equipment, and the risk of getting it wrong.
Because North Carolina labor runs at 0.92× the national rate, the DIY saving here is closer to the national norm. Weigh it against tool rental, waste disposal, permit responsibility, and the fact that remedial work almost always costs more than doing it right the first time.
How North Carolina compares with nearby states
North Carolina sits in the South region. Here is how neighbouring states price the same specification:
| State | Cost per linear ft | vs North Carolina |
|---|---|---|
| Mississippi | $16.38 – $40.95 | Lower than North Carolina |
| Arkansas | $16.47 – $41.18 | Lower than North Carolina |
| Alabama | $16.56 – $41.40 | Lower than North Carolina |
| West Virginia | $16.74 – $41.85 | Lower than North Carolina |
| Oklahoma | $16.83 – $42.08 | Lower than North Carolina |
| Kentucky | $16.92 – $42.30 | Lower than North Carolina |
Getting an accurate number for your project
Everything above is a planning range. Enter your real dimensions and specification to get a figure with North Carolina rates already applied:
Open the wood fence calculator →Then get three written, itemised quotes. Make sure each one specifies the same dimensions and the same grade of material — that is the only way a comparison means anything.
Frequently asked questions
How much does wood fence cost in North Carolina?
In 2026, wood fence costs $17.28 to $43.20 per linear ft in North Carolina. For a 150-foot run, the installed total typically lands between $2,592 and $6,480, with most projects near $4,536.
Is wood fence more expensive in North Carolina than the national average?
North Carolina is about 4% below the national average. The driver is a construction wage index of 0.92 times the national figure, applied to the roughly 50% of the project cost that is labor.
Which parts of North Carolina are most expensive?
Charlotte, Raleigh, and Greensboro price above the statewide average because of higher wages, stricter permitting, and tighter site access. Rural counties typically run around 7% below the state figure.
Do I need a permit in North Carolina?
Most municipalities in North Carolina require a permit for work of this type and value. Budget around $400 and confirm with your local building department before work starts, since requirements vary between cities and counties.
How deep is the frost line in North Carolina?
The frost line in North Carolina is roughly 12 inches. Footings and posts must extend below that depth to avoid frost heave, which adds excavation and material to the job.
When is the cheapest time to book this work in North Carolina?
North Carolina allows year-round work, so there is no hard seasonal shutdown. The practical constraints are summer heat, which can force early-morning pours and rain delays in the wet season. Late autumn and winter are often the quietest and cheapest times to book a crew.
How much of the cost is labor versus materials?
Labor is about 50% of the installed price and materials about 50%. That split is why state wage differences move the total so much, and why material price swings move it less than people expect.
Why do contractor quotes in North Carolina vary so much?
Three things move a quote most: metro versus rural location, site access and preparation, and the specification itself. Two bids are only comparable when both list the same dimensions, the same grade of material, and the same scope of prep work.